Sunday, July 23, 2017

Circuit Diagram 500W Power Inverter using SG3526-IRFP540

Robotronicdiagram. - This is circuit diagram of 500W Power Inverter using SG3526-IRFP540 like in Figure 1 below. The main component in this circuit diagram is IRFP540 and other components. 

In here we will show you also the component parts used and the simple description of this circuit diagram and the last we will give you link to read more about this circuit from original source. 

Circuit Diagram 

Component Part
  1. R1______________15K_______________ = 1 pcs.
  2. R2______________22K_______________ = 1 pcs.
  3. R3______________2.7K_______________ = 1 pcs.
  4. R4______________10K_______________ = 1 pcs.
  5. R5______________12K_______________ = 1 pcs.
  6. R6______________4.7K_______________ = 1 pcs.
  7. R7______________47K_______________ = 1 pcs.
  8. R8,R22,R23______0.01 ohms / 5W ______ = 3 pcs.
  9. R9______________1K (PTC)___________ = 1 pcs.
  10. R10_____________ 8.2 ohms___________ = 1 pcs.
  11. R11______________16.9K______________ = 1 pcs.
  12. R12______________33 ohms____________ = 1 pcs.
  13. R13,R15, R18- R21_ 22 ohms___________ = 6 pcs.
  14. R14______________ 18 ohms___________ = 1 pcs.
  15. R16______________ 1K ________________ = 1 pcs.
  16. R17______________ 470 ohms___________ = 1 pcs.
  17. C1,C2____________220uF 16V____Electrolytic____= 2 pcs.
  18. C3,C7,C9,C10_____220nF 50V____Polyester_____= 4 pcs.
  19. C4______________1uF 50V________Electrolytic____= 1 pcs.
  20. C5,C6___________33nF 50V_______ Polyester_____= 4 pcs.
  21. C8___________2.2 uF 50V_______ Polyester_____= 1 pcs.
  22. D2__________1N4148_____75V 150mA Diodes__= 1 pcs.
  23. D2__________1N4002_____100V 1A Diodes__= 1 pcs.
  24. D4__________18V 1W_____Zener Diodes___= 1 pcs.
  25. D5,D6_______BY299______Didoes__________= 2 pcs.
  26. IC1_________LM393N____op-amp IC________= 1 pcs.
  27. IC2_________SG3526N or SG2526N IC______ = 1 pcs.
  28. Q1-Q6______IRFP540 mosfet______________ = 6 pcs.
  29. D1_________LED 3 mm red or as you need____ = 1 pcs.
  30. T1________220V / 12V-0-12V / 40A transformer__ = 1 pcs.
  31. PCBs,Heat sink, wires and others.

Circuit diagram like in figure 1 above is Circuit Diagram 500W Power Inverter using SG3526-IRFP540. According Eleccircuits site describe that as 200 watts inverter circuit. We use Q1, Q2 is the mosfet acts as a power output. That can withstand currents up to 18A. According to properties listed in the table of Figure 2. If the circuit is fully functional with maximum power of 12V x 18A = 216 watts. But in practice, the circuit should work up, it may be damaged. Therefore, it is designed to operate up to 200 watts.

Since we want the current more than 40A. But the power mosfet single, able to withstand current is 18A, therefore have to be 3 pcs. And When designing a circuit in a push-pull model thus requires a power mosfet 3 pairs.

We have the output current up to 54A which can withstand more demanding than 14A. It is good for the operation of the circuit. Because each power mosfet will not be overburdened. And the heat of the mosfet least, the lifetime of the life circuit.

In Figure 3 is the inverter circuit with a power output Increased at least 2 pairs and use the 12volts 40A transformer, so that the power output 500 watts.

Please read more this article from original source about Circuit Diagram 500W Power Inverter using SG3526-IRFP540 using link Here.

Thank you for your coming here in, we hope the article above will help you to know more about your information in electronic circuit design and other in this time. Please comment here when you want to share and other. Thank you.


Post a Comment

Let's share your idea with comment here